Competition Resins 1/25 Scale

Wide Rear Steel Wheel Pair 1/25

A pair of deep rear wheels. These are stock looking steel wheels with lug nuts, except they're wide to hold big rubber. Great for street racers, early Super Stock or Pro Stock and Rat Rods. Width/Depth = .33" (11/32")   Contains 2 resin wheels by...

MiniLite Road Racing Wheel Set 1/25

A set of four road MiniiLite Racing Wheels. Unlike the racing set of MiniLite wheels, these are all the same size.   Contains 4 resin wheels by Competition Resins, 1/25 scale.

Einstein Blower Hat and Base 1/25

Here's a different blower hat.  It's similar to the Janis style. Includes a plate with an injector distribution block. Overall height is 1.00". Three pieces in resin   By Competition Resins, 1/25 scale.    

Dual Quad Tunnel Ram Manifold 1/25

Set a pair of Dominator or Demon carbs on top of this manifold. Make sure you have room under your hood or cut a hole in the hood to allow for the height. Overall height is .43" (7/16"). Here's a photo of a real dual quad setup byRich Vitiritti. ...

S.C.O.T Blower 1/25

Here's a special blower for that Flathead engine. S.Co.T. is an abbreviation for 'Supercharger Company of Turin' (Torino), Italy. It was one of the most popular "roots" style blowers in the 1950's and popular today on Street Rods and Rat Rods...

Holley Dominator Carburetor (Pair) 1/25

A pair of nicely detailed Holly Dominator 4-bbl Carburetors. With single or dual carbs, you'll need a Fuel Junction Block (see ENGINE DETAILING). Also see the Braided Lines, Hard Lines, Soft Lines and Fittings along with the SMALL or LARGE 'T' fitting...

GM TH350 3-Speed Transmission 1/25

A nicely detailed General Motors 350 Turbo Hydromatic transmission. Molded in one piece with bellhousing. By Competition Resins, 1/25 scale

Pirelli Type Small Front Racing Tires 1/25

These front tires will work for a Gasser as well as a Pro Mod or street racer. These are slightly smaller than the Futurattraction Front Runner tires. These are semi hard tires but still flexible. Measurements:Outside Diameter = .98"Overall width = ...

Good Year Dragster Slicks 1/25

These are labeled '60's Goodyear Dragster Slicks but depending on the size you want, these will work for any racer. "Good Year" is in raised letters on both sides. These are slightly smaller than the Comp Resins' Pro Stock slicks. These are fairly...

Dodge 'Red Ram' HEMI Valve Covers 1/25

A pair of Dodge HEMI valve covers with lettering. DODGE and Red Ram are printed in raised lettering. The Dodge HEMI Red Ram was the most powerful stock engine in the '50's. Here are 2 real life examples.   Contains 2 resin pieces.

Pro Mod / Pro Stock Rear Wing 1/25

A one piece wing with an arch shape and small side spoilers. This is a typical wing for the Stratus body, but it can be made to fit many different cars and race classes. Dimensions: Width 2.5" Depth .625"   Resin, 1/25 scale

Drag Slicks Pro Stock 1/25

Pro Stock Drag Slicks.  Although the package is titled 70's style slicks, they will obviously work for many drag racing types. The slicks are a lower profile and smaller in general than other slicks I carry. These are fairly hard tires and extra...

53 Corvette Pro Mod Body '05 1/24

A really nice 1953 Pro Mod Resin Body. Features molded-in rear wing. The finish on the body is really smooth and crisp.   One resin body 1/25 scale, by Competition Resins  

41 Willys Pro Mod Body '05 1/24

The popular '41 Willys Pro Mod Resin Body. Features molded-in rear wing. The finish on the body is really smooth and crisp. Use Revell Pro Street Corvette Kit For Chassis.   One resin body 1/24 scale, by Competition Resins  

Stratus F/C Body '05 1/24

2005 Dodge Stratus Funny Car Resin Body. Body comes with Exterior & Interior Rear Spill Plates Use late model Revell funny car kit for chassis, 1/24 scale   One resin body with included items as outlined, 1/24 scale, by Competition Resins...

23 Pickup T Fuel Altered Body 1/25

 Includes: T Pickup Body Radiator Shell Front Wing              Photo of real T altered I have a one-piece 3D-printed Resin Chassis for this body. One resin body with included items as...

ET III Style Rear Wheels 1/25

ET III 'Bear Claw' style rear drag racing wheels. Popular in the '60's on street and drag machines.                         Photos of real wheels          ...

Mustang 2010-12 Pro Mod / Pro Stock Body 1/25

2010-2012 Mustang Pro Stock / Pro Mod Body. Kit includes: Hood Scoop Hood Scoop Blank Rear Wing Clear Headlight and Taillight covers I have a one-piece 3D-printed Resin Chassis for this body. One resin body with included items as outlined,...

Outlaw Super Cowl Hood Scoop 1/25

A raised 2-level hood scoop.   Molded in one piece. Contains 1 resin scoop, 1/25 scale.

Ford C4 Transmission 1/25

A Ford C4 automatic transmission. Contains 1 resin transmission, 1/25 scale

Ford C6 Transmission 1/25

A Ford C6 automatic transmission. Contains 1 resin transmission, 1/25 scale

12-Spoke Front Wheels 1/25

12-Spoke front drag racing wheels. 4 resin pieces makes 2 wheels, 1/25 scale, by Competition Resins.

Camaro 2012-13 Pro Mod / Pro Stock Body 1/25

  2012-13 Camaro Pro Stock - Pro Mod Resin Body Kit includes: Hood Scoop Hood Scoop Blank 2 Grill Inserts Rear Wing Translucent Red Tail Lights See SLIXX decals for two different Summit Racing body decals. Sheet #1 or...

Carbon Fiber Style Hat, Long 1/24

A round 3-hole hat that is typically seen in carbon fiber. This is a long version.  A shorter version is also available. Molded in one piece. 1/24 scale, by Competition Resins.

Shotgun Blower Hat 1/25

A 2-Hole 'Shotgun' Injector Hat.Molded in one piece. Contains 1 resin hat.

4-Hole Carbon Fiber Hat 1/25

A 4-Hole compact Injector Hat.  This is slightly raised and has 4 square butterflies. Molded in one piece. Contains 1 resin hat.

HEMI Injector Manifold 1/25

A fuel injector manifold for your HEMI engine.   Here's a fuel plumbing diagram for this manifold.The lines go to a distribution block in the center.      Velocity stacks are available to fit this manifold. File the little 'nubs' on...

Chevy Injector Manifold 1/25

A fuel injector manifold for your Chevy engine.   Here's a fuel plumbing diagrams for this manifold.The lines go to a distribution block in the center.      Velocity stacks are available to fit this manifold. Contains 1 resin piece.

PSI Blower 1/25

A PSI Blower in one-piece resin.For a 'roots' type blower, see the Kalbelco series of 671, 1471 and 1671 super chargers. This is a standalone blower - pulleys or other components are not included. Contains 1 resin blower by Competition Resins, 1/25 scale.

Challenger '08 - '10 Hood 1/25

A 2008-2010 Challenger hood in the 70's Shaker Hood style.   Contains 1 resin hood, 1/25 scale

Battery (pair) 1/25

A pair resin batteries to add detail for the trunk or the engine bay. Dress them up with manufacturer's decals found here and battery connectors here.   For multiple battery connections in Parallel or Series, look here.     Contains 2...

Carbon Fiber Style Hat, Short 1/24

A round 3-hole hat that is typically seen in carbon fiber. This is a short version.  A longer version is also available. Molded in one piece. 1/24 scale, by Competition Resins.

Cross-Ram Manifold & Carbs 1/25

A cross-ram & carburetor package.All items have locating pins for easy alignment. Consistis of: 1 Cross-Ram manifold 2 4bbl carbs 1 Air cleaner   1/25 scale by Competition Resins

Enderle Hat 1/25

A 3-hole late model Enderle injection hat.Molded in one piece. Contains 1 resin hat, 1/25 scale, by Competition Resins.

1471 Kobelco Blower with Blanket 1/25

A Kobelco 1471 Blower with a restraint blanket molded in.Made in one piece.This a blower only - pulleys or other components are not included. Check out this photo for an idea of which blower you need. Contains 1 resin blower.

Wrinkle Wall Drag Slicks, 1/25

Current style Drag Slicks with a wrinkled sidewall.  Dimensions are listed below to see if they fit your needs. Each side of these tires will accept a different size wheel. Tire Measurements: Width .60",  15.25mmWheel opening .660", 16...