VCG Resins by Reese

3" Cowl Hood Scoop 1/25

Low profile hood scoop. Full width rectangular opening in the front, flat top, sloping down at the rear. Measures: Width = 7/8" Length = 1-7/8" Height = 3/16"   1 resin piece by VCG...

3-Hole Tri-Power Scoop, Short 1/25

A 3-hole scoop/hat in a triangular shape. Overall length is 1" A longer version of this scoop is also available.   2 resin pieces by VCG Resins, 1/25 scale.    

427 Chevy 'Starter' Engine with Tranny 1/25

This is a basic 427 engine and transmission, without induction. Includes Block Heads Valve Covers Oil Pan Transmission    Assembly required. One complete engine, resin, by VCG...

BBC 572 Blown/Carb Engine 1/25

A blown, dual carb, 572 cubic inch BBC engine. Ideal for that screaming street machine or hot rod. Engine includes:    572 Block Heads 572 Valve Covers (with raised '572'...

BBC 572 Tunnel Ram, 2-Carb Engine, 3D 1/25

A 3D-printed BBC 572 with tunnel ram intake and dual carbs. Ideal for that screaming street machine or hot rod. Excellent detail and it has locating tabs for easy assembly and alignment of parts...

BBC CrossRam Kit, 3D 1/25

A 3D-printed BBC CrossRam induction system. Ideal for that screaming street machine or hot rod. Nicely detailed. Manifold has a distributor and t'stat housing. Includes:    Timing...

BBC Valve Covers with Bowtie Logo 1/25

A pair BBC valve covers with the Chevy Bowtie emblem on the surface. NOTE: I highlighted the emblem on one valve cover to show the image better.  One pair of valve covers, resin, by VCG...

Heavy Duty 4X4 Transmission 1/25

A nicely detailed Heavy Duty transmission for your 4X4.   Resin, 2 halves, by VCG Resins, 1/25 scale.

Interior Speaker Set 1/25

CONTAINS: Two large square speakersFour of 8" diameter speakersFive flat panels All pieces are resin. By VCG Resins, 1/25 scale.    

Nitrous Oxide NOS Decals, 1/25

NOS decals for added realism. Contains one main NOS logo/label and one Warning label. Dimension: .32" x .39",  8 x 10mm         Photo of actual NOS...

Optima Battery & Decal 1/25

An accurate representation of the popular Optima battery that is 3D-printed and includes a decal. Battery is two pieces (top and bottom) and you have to paint the battery and then apply the...

Oval Scoop, Short 1/25

A shorter scoop with a round/oval opening. The rear is slightly sloped to fit against the windshield.  It can be shaped to fit your installation.   Resin, by VCG Resins, 1/25 scale.  ...

Power Steering Pump w/ Pulley 1/25

Here's an item that will detail that engine bay - a power steering pump.  It's modeled after the popular Saginaw pump. Includes an aluminum pulley. Check here for a high pressure hose and here...

Pro Mod Front Motor Plate, Water Pump, Dry Sump 1/25

A detailed front motor-mount plate. INCLUDES: Dry Sump Reservoir (2-pieces)Electric Water PumpOil Filter Overall width = 1.25"  Six resin pieces, by VCG Resins, 1/25 scale

Pro Street License Plate Decal 1/25

A pair of license plate decals with PRO STREET written on the face. These are New Your plates with a red Statue of Liberty on the left side. The lettering is in blue.   Two decals on one sheet,...

Running Boards, Flat Step, 1/25

A pair of running boards with a flat step along its length.   Resin, 1/25 scale by VCG Resins.  

Single MSD Coil Pack 1/25

An MSD coil for your racing ignition system. This would feed an MSD Pro Mag or other high voltage magneto.   One resin piece by VCG Resins, 1/25 scale.    

Snorkel Hood Scoop, 3D 1/25

A long sloping scoop with a rectangular opening and rounded corners. It has a flange around the perimeter where it meets the hood. Overall length: 1-1/2" Height at tallest point:...

Tunnel Ram Kit 1/25

Two Dominator carbs on a tunnel ram manifold.   Six pieces, resin, by VCG Resins, 1/25 scale.