Front Strut Kit for Aluminum Wheels, TBM Rotors 1/25

This is a complete 28 piece strut front end kit for 5-bolt wheels (a strut set for spindle wheels is found here. The nose of the 3D spindle is designed to center in Futurattraction's 5-bolt wheels and includes 3D-printed hubs to fit to the back...

Rack & Pinion Set 1/25

 A complete Rack & Pinion set for your chassis. This fits a chassis that is about 1” wide (outside dimension). Consists of: 3D printed steering rack (0.80" overall length)Two rubber bootsStainless steel tubing.(3" x .022" OD)Photo...

Carbon Fiber Seat 1/25

A simple one-piece seat for a dragster, FC, P/M, etc. The seat has reliefs in each side to allow for seat belts or safety harness material. My seatbelt/harness material will fit the seat reliefs. Dimensions: Width at top: .87"Width at bottom: ...

Blower Starter Bracket, 1/16

Unless your blown engine has its own starter, you'll need to start it with a blower starter. This bracket holds the blower starter and will add that special touch of detail to your engine. Here is a photo of a real-world starter. The pins fit into the...

Front End Mounting Brackets 1/25

These brackets are intended to simulate the mounting brackets used to locate removable front ends from drag or other styles of cars.   Photo etched, 1/25 scale, by Futurattraction.   Photo Etched, (2 pr) 

Rust Streaks Weathering by AK Interactive, FREE

This is a FREE downloadable PDF file for weathering rust effects using AK Interactive's Rust Streaks Weathering Set. You don't have to buy anything to download this file, but you still have to go through the checkout procedure. Just add this to...

Fuel Stain Weathering by AK Interactive, FREE

This is a FREE downloadable PDF file for weathering engines using AK Interactive's Fuel Stains Weathering Set. You don't have to buy anything to download this file, but you still have to go through the checkout procedure. Just add this to your cart and...

Heavy Muddy Weathering by AK Interactive, FREE

This is a FREE downloadable PDF file for weathering muddy and wet effects using AK Interactive's Heavy Muddy Weathering Set. You don't have to buy anything to download this file, but you still have to go through the checkout procedure. Just add...

Rust Streaks Weathering

This will give you the look of rust on any type of engine or metal object.   This enamel-based paint just needs to be painted on. Apply with a brush in different layers of different intensities for the most realistic effects...

Fuel Stains Weathering

This will give you the look of fuel stains on any type of engine or metal object.   This enamel-based paint just needs to be painted on. Apply with a brush in different layers of different intensities for the most realistic effects...

Heavy Muddy Weathering 4-Bottle Set

This weathering set contains everything necessary to create realistic mud & water effects on any vehicle. The set contains four 35ml bottles of pigments and a plaster to give depth and volume to the mud. Also included is a product for doing...

CA Glue Replacement Tips, 3-Set

This is a no-brainer to have on your workbench. A set of three CA Glue replacement tips. Start off with new tips which fit bottle sizes, 1/2oz and 1oz.   Three CA glue replacement tips, by Bob Smith Industries.  

Uncure CA Glue Debonder, 1oz

This is a no-brainer to have on your workbench. It not only unsticks your fingers to something (most likely another finger), but it softens CA glue on parts.  Used on your skin, it will dissolve the CA in about a minute. Apply on bonded skin and...

1969 Yenko Camaro, 1/25

The initial 1967 release of the Chevrolet Camaro had these engine options: One of two straight 6-cylinder engines; Small-block in 302-, 327-, or 350-cubic-inch displacement; Big Block 396. The vaunted 427 was reserved for mid-size cars,...

426 HEMI Front Motor Plate, 1/16

A photo etched front motor plate for a Revell HEMI engine. Includes 4 chassis tabs for bolting on to the motor plate. Sized to fit an approximate chassis width of 1.16" (center to center). Will replace existing Revell kit mounts. For the best fit,...

RBS Square 4-Hole Hat with Butterflys, 1/16

This is a CAD designed replica of an RBS Square 4-Hole Injector Hat, in 1/16 scale. The intake openings are hollowed out. Small holes across the front openings are provided for a rod to connect the butterflys to your throttle linkage and barrel valve...

Front Strut Gusset Kit 1/16

These gussets are intended to add both structural as well as added detail to the upper strut mount. There are enough for approximately seven cars. These gussets are intended to fit around a 9/64" (.140)" diameter upper strut mount.    ...

Blower Belt, 1/16

This 1/16th scale ribbed blower belt fits Revell Hemi engines, as well as other engines, but the pulley cogs may be different.  It is cast out of urethane rubber and stretches enough to fit nicely over the kit pulley setup.  It can fit...

Blower Restraint Plate, 1/16

This restraint plate sits under the blower and restraint straps would fasten to the slots and go over the blower to hold it down in the event it would blow up. It is universal to all blowers.   This photo etched piece is etched out of .016"...

Throttle Linkage Set, 1/25

A throttle linkage set with pins added to the ends of the linkage components. This will provide a more stable attachment point for linkage rods, etc. Depending on your attachment, the pin may have to be bent 90 degrees.   Photo etched...

Dana Rear End, Standard Width, Bare 1/25

Here is a Dana rear end in a standard width, molded in white resin. Overall length between axle tube ends is 2.25" The width can be shortened to suit your build by cutting the axle tubes. A Dana rear with the brake kit is available here.   See...

Stock Width 9" Rear End 1/25

Here is a nicely detailed 9" Ford OEM-style rear. This version is the stock width (2-1/4") and there is a narrowed width Ford 9" found here. This rear is also available with an included brake set and in either in black or white. The width can be...

Holley Dominator Multi-Media, Pair 1/16

Holley Dominator multi-piece Carb Kit with Photo Etch Air Horn and Linkage Carbs separate into separate main body, metering blocks and float bowls for extra detailing! The carb bodies are based off 3D-printed masters. They are supplemented with...

Vintage Graphics Decals, 1/25

Lots of early Pro Stock & Super Stock related graphics. Includes: All major car manufacturers Hurst Shifter Hooker Headers Champion Wynn's Super Stock racing classes and more - see the product photo  Measures 7" x 4.75"   One...

Gasser Graphics Decals #2, 1/25

Lots of Gasser and Rat Rod related graphics. Includes: Hurst Shifter Mooneyes (2 sizes) American Flag Letters to make A/G, B/G, etc for gasser classes and more - see the product photo  Measures 7" x 4.75"   One decal sheet, by...

Round Air Cleaner, Spun Aluminum, 1/25

A realistic round spun aluminum Air Cleaner. It has a screen air filter between the top and bottom halves. Dimensions: Diameter - .45" Overall Height - .19"   No assembly required.   By Parts by Parks, 1/25 scale.

3-Pulley Set, 1-Groove 1/25

A set of three spun aluminum V-groove pulleys. Consists of three single groove pulleys. Includes belt material. The package list this pulley set for SBC engines in AMT's '33 Ford (kit #6714) and AMT's '34 Ford (kit #6686) but these can be used on any...

Engine Detailing Kit Plus #2, 1/25

An engine wiring and plumbing kit Consists of: Radiator hose, black Heater hose, red Black detailing wire (battery, ignition, etc) Red detailing wire (battery, ignition, etc) Two sizes of aluminum line  By Parts by Parks, 1/25 scale.

Wire Wheel w/ Wide Whitewall 4-Set, 1/25

Five chrome wheels and four wide whitewall, narrow tires.  Therods. tires would be excellent for customs, rat rods and hot rods. AMT states the fitth wheel is for a Continental Kit. I thought a Continental Kit included a tire because it was your...

1967 Camaro Z28, 1/25

The initial release of the Chevrolet Camaro was 1967. The Z28 was their high performance version. This AMT Z28 is new for 2022 with new tooling.   Assembly Required. By AMT, 1/25 scale

Quick-Turn Fasteners, 1/24-1/25

Your typical Dzus fastener except a little smaller than others which make them less obtrusive. A total of 72 fasteners will go a long way.   By Detail Master, 1/24-1/25 scales.

Dry Sump Oil Resevoir, 3D, 1/25

Pro Stock, Outlaw or super-mean street machine, if you have a dry sump oil system, you need a reservoir tank to hold the oil. This 3D-printed tank is loaded with detail. It includes a filter on the side, inlet/outlet barbs and mounting arms. If you...

BBC Headers, 3D, 1/25

One pair of realistic BBC headers. These don't drop down very far and they are rear exit.   Designed by @Mattys_custom_scale One pair of headers, 3D-printed by 3D Scale Kreations

Carbon Fiber Decal Sheet, Black/Bronze 1/20

This is the typical twill weave carbon fiber you'll find on parts for weight reduction while maintaining strength. The decal is printed with a black twill weave pattern over a bronze metallic base and includes instructions. Uses...

Spark Plug Wire Loom Set, #1 1/24-1/25

This is a traditional set of wire looms. Includes four pairs of different styles, plus the typical wire separators for one to four wires. These have a good shine to them and don't need to be painted.   Hole size for spark plug wires in the 1, 2,...

Thermostat Housing 1/16

Here is a detail item you won't find everywhere - a thermostat housing for any engine. A .157" rubber line (equal to a 1:1 size of 2-1/2" radiator hose) will fit over the outlet neck found here.   Contains one thermostat / water neck...