MSD Pro Mag 44 with Dual Drive, 1/25

A 3D-printed MSD Pro Mag and a Drive to add a second mag. It consists of three pieces - Body, Cap and Cover. A MSD decal is included but not shown in the photos. The ignition wires pass through the openings of the cap. Make the wires long enough to...

DART BBC Tunnel Ram Engine 1/25

A 3D-printed Dry Sump BBC engine based on a DART Billet engine. Features: Detailed Block Enlarged Heads Tunnel Ram Manifold Two Demon Carbs Distributor Tall 'DART' valve covers Timing Cover, Water Pump & Alternator Rubber Fan Belt Oil...

DART BBC Tunnel Ram Dry-Sump Engine 1/25

A 3D-printed Dry Sump BBC engine based on a DART Billet engine. Oil pan and external oil pump are pre-drilled for hoses/fittings. Strip end off Braided Line and insert core into hole.Harmonic Balancer and oil pump will accept 1mm diameter pulley shafts...

Round Air Cleaner, Low-Profile, Spun Aluminum 1/25

Very nice looking air Cleaner, 5/8" diameter x 5/32" high Spun Aluminum. Polished with slight peak in top center. Includes mesh around air cleaner. It has a flat bottom. This is a typical wide, low profile air cleaner. One complete aluminum piece by...

Round Air Cleaners, High-Profile, Spun Aluminum 1/25

Very nice looking air Cleaner, 9/16" diameter x 7/32" high Spun Aluminum. Polished with slight peak in top center. Includes mesh around air cleaner. It has a flat bottom. This is fairly high, so check for hood clearance. One complete aluminum piece...

Weld V-Series Aluminum Rear Wheels 1/16

A detailed pair of Weld V-Series aluminum rear wheels In 1/16 scale. These match Futurattraction's V-Series front wheels.  These replicate Weld's 16" x 16" wheels. Three different inserts stack to create a 3-dimentional look. The beadlock...

Weld V-Series Front Wheels, 1/16

A pair of  Weld's V-Series 15" x 3.5" spindle-mounted front wheel. Includes three .20" thick 6061-T1 aluminum center inserts that stack for a 3-dimentional look. The outer-most insert is slightly smaller to represent the 'stepped' look. Also...

Weld Magnum Aluminum Rear Wheels 1/16

A detailed pair of Weld Magnum aluminum rear wheels In 1/16 scale. These match Futurattraction's Magnum front wheels.  These replicate Weld's 16" x 16" wheels. Three different inserts stack to create a 3-dimentional look. The beadlock rings...

Weld Magnum Front Wheels, 1/16

A pair of  Weld's Magnum 15" x 3.5" spindle-mounted front wheel. Includes three .20" thick 6061-T1 aluminum center inserts that stack for a 3-dimentional look. The outer-most insert is slightly smaller to represent the 'stepped' look. Also...

Billet Specialties CO7 Aluminum Front Wheels, 1/16

Here is Billet Specialties' Comp7 15" x 3.5" spindle-mounted front wheel. Includes three .20" thick 6061-T1 aluminum center inserts that stack for a 3-dimentional look. Also includes spindle caps. These will fit Futurattraction's 1/16 scale Front...

Billet Specialties CO7 Aluminum Rear Wheels 1/16

A pair of Billet Specialties aluminum rear wheels In 1/16 scale. Here are matching front wheels. These replicate the Comp7 Series 16" x 16" wheels. Three different inserts stack to create a 3-dimentional look with one having a black center. The...

Weld AlumaStar Aluminum 5-Spoke Narrow Front Wheels, 1/16

An excellent reproduction of Weld's AlumaStar 15" x 3.5" spindle-mounted front wheel. Includes three .20" thick 6061-T1 aluminum center inserts that stack for a 3-dimentional look. The outer-most insert is slightly smaller to represent the 'stepped'...