1/25 - 1/24 Scale

Truck Logos & Warnings Decal Sheet, 1/25

This decal sheet is perfect for detailing your long truck. Decals included: DOT Information Wide Load (with stripes) Wide-Turn notice Combustible warning Flammable warning Radioactive warning Mud Flap Girls Various other decals for...

Terry Labonte NASCAR #5 Corn Flakes 1/24

Kellogg's Corn Flakes #5 Monte Carlo driven by Terry Labonte. The body lifts off to reveal the NASCAR interior and engine. Purchase 2 or more and receive a 10% discount on each. Box is unopened, sealed and new. Molded in white. Assembly required...

Peterbilt Photo-Etched Logos, 1/25

The famous Peterbilt oval logo with shiny die cast letters. The background is recessed below the Peterbilt letters and the oval outer ring. A thin red wash will fill this recessed area leaving the letters and oval rim. Put these on the hood sides, cab...

Pre-Wired Distributor, Red Cap, 90-Degree Boots 1/25

An authentic looking distributor with 90-degree black boots at the cap and 90-degree black boots at the spark plug end. Includes a nicely detailed cap, base and aluminum stem along with pre-assembled spark wires with boots 90-degree black boots are...

Pre-Wired Distributor, Red Cap, Straight Boots 1/25

An authentic looking distributor with straight black boots at the cap and at the spark plug end. Includes a nicely detailed cap, base and aluminum stem. Also includes a center coil wire which is indicated with its wire end bent over. Completely...

Pre-Wired Distributor, Black Cap, Straight Boots 1/25

An authentic looking distributor with straight black boots at the cap and at the spark plug end. Includes a nicely detailed cap, base and aluminum stem.   Also includes a center coil wire which is indicated with its wire end bent over...

SBC Tunnel Ram & Lenco 1/25

An all new, highly detailed, complete 429cid Ford engine with the Boss 429 cylinder head/valve cover combo. Perfect for that '80s to '90s Pro Stock racer. Included is everything needed to build a well detailed, carbureted engine with a...

Pinstripe Decals #1 White, 1/25

These aren't found anywhere else and they are really intricate. Mount them on dashboards, hoods, roofs, trunks, pickup tailgates and more. This design set is also available in black, for light-color painted backgrounds. Includes 18 different pairs and...

572 Valve Cover Decal Sheet - White 1/25

Five pairs of "572 CHEVROLET" valve cover decals with white lettering. Decal sheet measures 1" x 1.75"   One decal sheet, by STS Decals, 1/25 scale.

'23 T Fuel Altered Tubular Full Chassis, 1/25

A complete one-piece 3D-resin-printed chassis. This fits Competition Resin's '23 T Altered body, but it may fit your needs too (see dimensions below). Made of resin so easy modifications can be made by cutting, sanding and use of CA glue...

Weld AlumaStar Front & Rear 4-Wheel Set 1/24

A 4-wheel set of Weld AlumaStar racing wheels in 1/24 scale. SAVE $5.00 OVER BUYING THE FRONT AND REAR WHEELS SEPARATELY. Includes: Outer Aluminum Rims Inner and Outer Photo Etch Center Inserts Hubs A Front Strut spindle kit is available...

Racing Seat Belt, Harness, Hardware & Blue Belt Material 1/25

Photo etched lap and harness seat belt hardware with blue, textured belt material. One package will make 2 sets. Includes photo-etched buckles, harness material and directions.   By Gofer Racing, 1/24-1/25 scales.

Black Soft Line .050", 1.3mm

This black soft line has a .050" (1.3mm) diameter.  See the sizing table below to determine the real world size at your scale.  This is real rubber and it will bend and drape easily without kinking.  Depending on your scale, typical uses...

Ignition or General Wire, Yellow .014"

This bright yellow wire can be used for any electrical need. It is .014" diameter which is equal in real life to 5/16" or 9mm at 1/25 scale. At 1/16 scale, this wire would be equal to 1/4" diameter. Uses are spark plug wires, battery wires, electrical...

RBS Square 4-Hole Hat with Butterflys, 1/25

This is a CAD designed replica of an RBS Square 4-Hole Injector Hat, in 1/25 scale. The intake openings are hollowed out. Small holes across the front openings are provided for a rod to connect the butterflys to your throttle linkage and barrel valve...

Front Brake Kit , Slotted Rotor .093" Spindle Diameter 1/25

A really nice brake set for the front wheels. This slotted rotor set is designed to work with a .093" (3/32) spindle diameter and allows the use of separate calipers and PE brackets. 3D calipers (2 pieces per caliper) 3D Hubs 3D Spacers PE drilled...

Good Year Tire Decals - Yellow, 1/25

Set includes Yellow Goodyear tire water slide decals. A quantity of 24 Good Year #1 decals (all the same size)   These water slide decals are the thinnest you'll find, making the edges blend into the body. Includes instructions...

Good Year Tire Decals Big & Little - White, 1/25

Set includes White Goodyear tire water slide decals in 'big 'n little' sizes. Sixteen of each size for a total of 32 decals. These water slide decals are the thinnest you'll find, making the edges blend into the body.   One 5.5" x 4" Sheet,...

Early Racing Contingency Decals #2, 1/25

You'll find manufacturer logos here that you won't find elsewhere. Early Mickey Thompson Sun Tach Iskenderian Lakewood Belll Helmets M&H Mr Gasket M&H RaceMaster and more These water slide decals are the thinnest you'll find, making...

License Plates - New Jersey, 1/25

Various New Jersey License Plates. Printed on high quality gloss paper with 2400 resolution.  Full color clear vector graphics for the best readable print. Each set includes the 30 plates as displayed. This product is NOT  a water slide...

Early Racing Contingency Decals #1, 1/25

You'll find manufacturer logos here that you won't find elsewhere. Early and Current Edelbrock Early Holley RaceMaster 'Cherry Bomb' Red Devil Oil B&M (3 different pairs) Halibrand Cal Custom and more These water slide decals are the...

MSD Pro Mag 44 Pre-Wired 1/25

Here's a 3D-printed MSD Pro Mag with your color choice of spark plug wire already installed.Drill a hole in your block and insert this MSD magneto. Route the wires to the spark plugs and don't forget the Spark Plug Boots, for even more detail. Specify...

Spark Plug Boots 90Deg, 3D, 1/25

A package of ten, 90-degree, 3D-printed, spark plug boots, ideally suited for the distributor cap (see photo). Enough for eight spark plugs boots at the distributor, plus two boots for the coil wire.  You will need another set of boots for the...

Spark Plug Boots 45Deg, 3D, 1/25

A package of ten, 45-degree, 3D-printed, spark plug boots.   When cutting the boot from the tree, a stem remains to insert into the head's spark plug hole (use a #70 drill bit).   The hollow end accepts Pro Tech's Spark Plug Wire. Pro...

Wheel Beauty Rings, Round 1/25

A set of four polished aluminum beauty rings with a round edge. Polished aluminum rings to set those wheels off and a period correct look for the '50's - '60's. They would look great next to the Baby Moon Hubcaps by Parts by Parks. Measures 5/8"...

3D-Printed 4bbl Carburetor 1/25

Highly detailed Holley Street/Strip 4-bbl Carburetor.With single or dual carbs, you'll need a Fuel Junction Block (see 1/25 SCALE/ENGINE RELATED/FUEL MANAGEMENT). Also see the Braided Lines, Hard Lines, Soft Lines and Fittings along with the SMALL or...

Front Strut Spindle Suspension Kit with Drilled Rotors 1/25

Here is a complete front strut kit, with all of the parts needed for a detailed front suspension. This is a static suspension and not functional. Kit includes (28 pieces): 3D-printed strut bodies/spindles (resin pieces shown in photo) Aluminum tube...

Racing Seat Belt, Harness, Hardware & Black Belt Material 1/25

Photo etched lap and harness seat belt hardware with black, textured belt material. One package will make 2 sets. Includes photo-etched buckles, harness material and directions.   By Gofer Racing, 1/24-1/25 scales.

Racing Seat Belt, Harness, Hardware, Red Belt Material 1/25

Photo etched lap and harness seat belt hardware with red, textured belt material. One package will make 2 sets. Includes photo-etched buckles, harness material and directions.   By Gofer Racing, 1/24-1/25 scales.

1965 Mustang Tear Drop Hood - AMT 1/25

A tear drop bubble that can be cut out and mounted on your hood or it's made to fit the AMT stock '65 Mustang kit.   Here's an example of the hood on a 'Russ Davis Ford' Mustang.          Contains 1 resin...

Front Strut Kit for Aluminum Wheels, TBM Rotors 1/25

This is a complete 28 piece strut front end kit for 5-bolt wheels (a strut set for spindle wheels is found here. The nose of the 3D spindle is designed to center in Futurattraction's 5-bolt wheels and includes 3D-printed hubs to fit to the back...

Stock Width 9" Rear End 1/25

Here is a nicely detailed 9" Ford OEM-style rear. This version is the stock width (2-1/4") and there is a narrowed width Ford 9" found here. This rear is also available with an included brake set and in either in black or white. The width can be...

Wire Wheel w/ Wide Whitewall 4-Set, 1/25

Five chrome wheels and four wide whitewall, narrow tires.  Therods. tires would be excellent for customs, rat rods and hot rods. AMT states the fitth wheel is for a Continental Kit. I thought a Continental Kit included a tire because it was your...

Injector Stacks - Long 1/24-1/25

Smaller, polished aluminum injector stacks for a Hilborn style induction system. Pack contains 8 stacks, polished aluminum with a flared top. . The stacks are hollow with a 'pin' at the bottom for easy mounting Dimensions per back of...

Late '50s MoPar Hubcaps 1/25

A set of four polished aluminum hubcaps found on 1950's MoPar's. Almost a 'moon' hubcap, but they come to point in the center. They're similar to these '57 Plymouth hubcaps, but they're entirely smooth.   Real aluminum hubcaps to set off your...

Micro Weld

NOTE - CANNOT SHIP INTNATIONAL OR BY AIR TO DOMESTIC LOCATIONS Microscale's Micro-Weld is a styrene solvent cement that will provide the strongest bond for pieces that you want to stay together. Building that chassis with styrene rod? You need...