Fuel Line (solid core) 1/25

This line can be used for fuel, oil, water or other transfer hoses.It has a solid copper core to hold its shape.Use hex fittings sized at .025".Each package contains one coil .024" x 3', color black, by Pro Tech.

Pre-Wired Distributor 1/25

Here's a machined aluminum distributor body with your color choice of spark plug wire already installed.Drill a hole in your block and insert this distributor. Route the wires to the spark plugs and don't forget the Pro Tech Spark Plug Boots, for even...

Performance License Plate Set 1/43

Performance license plates for added realism.   NOTE THIS IS 1/43 SCALE ONLY   Plates included are:   Chevrolet USA-1 Chrysler Dodge Ford Motorsports Ford Lincoln Mercury Mercury Mopar Mustang Plymouth Today's...

State License Plate Set 1/43

State license plates for added realism.   NOTE THIS IS 1/43 SCALE ONLY   Plates included are: ArizonaCanadaColoradoFloridaIllinoisMichiganMarylandNew JerseyNew YorkTennessee Also, see the license plate frames. One set of 16 plates...

Performance License Plate Set 1/25

Performance license plates for added realism.   Plates included are:   Chevrolet USA-1 Chrysler Dodge Ford Motorsports Ford Lincoln Mercury Mercury Mopar Mustang Plymouth Today's Chevrolet   Also, see the other state license plates along...

State License Plate Set 1/25

State license plates for added realism.   Plates included are: ArizonaCanadaColoradoFloridaIllinoisMichiganMarylandNew JerseyNew YorkTennessee Also, see the license plate frames.   One set of 16 plates printed on paper, by Pro Tech.

Parachute Kit 1/25

This is the ultimate in a 1/25 scale drag chute - Contains an inner resin parachute core with an outer textured material to simulate the actual parachute jacket material.  Don't rely on flat black paint anymore. Color the material any color you want...

Hood Pin Set 1/25

One-piece (pin and plate) hood pins that are photoetched. Contains 12 photoetched hood pins per pack, by Pro Tech.

Detailing Wire .007"

Very small wire to be used for ignition wiring, computer connections, gauges, etc.Available in the following colors:BlackRedBlueYellowOne package of wire .007" x 3', by Pro Tech.

Spark Plug Boots Black 1/25

Rubber boots ready to use as is, for straight boots, or cut them and glue at a 90 degree angle for angled boots.Use in combination with your choice of color Pro Tech Spark Plug Wire.Each pack contains 8 black boots, by Pro Tech.

Radiator or Heater Hose, .070" OD

This solid core wire is used as a 1-3/4" radiator hose or other larger transfer hose at 1/25 scale.  At 1/16 scale it equals a 1" diameter hose, which is closer to a heater hose. It has an outside diameter of .070" It will hold its shape when...

Heater Hose 1/25

This copper core wire is used as a small heater hose or other transfer hose. The copper core will hold its shape when formed into place.  Cut the outer skin back, at the ends, just enough to leave a stub to insert into a drilled hole.Use hex...

Spark Plug or Large Detailing Wire 1/25

Choose a color for your spark plug wires.This can also be used for large detailing wire, if the other Pro Tech wire choices aren't large enough.Available colors:BlackRedBlueYellowOrangeGrayOne length of wire .018" x 3', by Pro Tech.Specify color.

Barry Grant DEMON 4bbl Carburetor 1/16

Detailed Barry Grant 4bbl CarburetorWith single or dual carbs, you'll need Pro Tech's 1/16 scale Fuel Junction Block.Also see the Braided Lines, Hard Lines, Soft Lines and Fittings along with the T fitting to split the fuel line to each carb. One...

Holley Dominator 4bbl Carburetor 1/16

Detailed Holly Dominator 4bbl CarburetorWith single or dual carbs, you'll need Pro Tech's Fuel Junction Block.Also see the Braided Lines, Hard Lines, Soft Lines and Fittings along with the T fitting to split the fuel line to each carb. One per...

Drag Racing Full Face Helmet 1/16

Detailed Full Face Helmet. Ready for your custom paint design.  Looks right at home on the cockpit seat or the hood of that Pro Mod car. One per package. Resin

Drag Racing Parachute 1/16

Detailed Drag parachute.One per package.Resin

Barrel Valve 1/16

A barrel valve is located on the left side of a supercharged engine injector hat. The fuel input is via a braided line from the fuel pump and 2 outlet braided lines go to 2 fuel junction blocks (see ENGINE DETAILING).Designed for Pro Tech .035 Braided...

Dual Remote Oil Filter 1/16

Each package contains 1 adapter and 2 oil filters.   See the Braided Lines and Fittings to complete the plumbing of the oil lines. Adapter is metal cast and can be polished.  Filters are machined aluminum   

Aluminum Oil Filter 1/16

Each package contains 1 filter. Machined aluminum  

MSD 7 Ignition Box 1/16

Each package contains 1 MSD 7 ignition box. See 'Detailing Wire, Small' to enhance this item.Resin 

MSD 6 Ignition Box 1/16

Each package contains 1 MSD 6 ignition box. The casting of this box shows the ribs and area for the MSD logo. The photo shows two Pro Tech MSD boxes with MSD labels copied from an automotive magazine and reduced. These are not included with the MSD 6...

Blown Engine Fuel Injection Block 1/16

Fuel Injection Block for supercharged engines. This is the fuel block that is located behind the injector hat and behind the blower which feeds the manifold. Use Pro Tech?s .035 Braided Line along with the corresponding fittings for the fuel feed line to...

Carburetor Fuel Junction Block 1/16

For your single or dual carburetor setups.  Made with molded-on fittings.Use .035 Braided Lines and Fittings and large T fitting. Each package contains 1 Fuel Junction Block, by Pro Tech. Resin cast

Aluminum Ignition Coil 1/16

Machined aluminum ignition coil with rubber boot.Use with your color choice of Pro Tech Spark Plug Cable.

Distributor Kit 1/16

Resin distributor, shaft and boot material. The cap has 'starter' holes to drill out and insert the spark plug boot which is cut from the included material. Refer to the photo showing a completed distributor. Assembly and painting are not included...

Throttle Linkage 1/16

Whether it's a blown engine, injected or carbureted, these photoetched pieces will detail your throttle linkage. For the metal linkage that fit into the holes, use the .014 and .020 aluminum lines.  These are stiff enough to hold...

Rod Ends/Link/Heim Kit 1/16

Cast metal parts for your suspension or throttle linkage detail.  Can be used for heim joints/rod ends in suspension areas like a 4-link rear end, panard bar or front radius rods. Use in combination with Pro Tech's Throttle Linkage kit for a...

Roll Bar Padding 1/16

Rubber tubing for roll bars.Can also be used for other larger water/coolant hoses.At 1/16 scale, this would be equal to 1.5" ID and 3.5" OD.At 1/12 scale, this would be equal to 1.25". ID and 2.5" OD.Black.

Mallory/MSD Ignition Coil 1/16

Modeled after a Mallory Ignition Coil. Also looks very similar to a MSD Ignition Coil. Photo of completed piece is for reference only. Painting, wires and decals are not included. Each package contains 1 coil. Resin 

Aluminum Gas Cap 1/16

Excellent detail for your race car fuel cell, hot rod Moon tank and other tanks like an oil tank on a Funny Car, Pro Mod or Dragster.Can also be used for a radiator cap, engine oil breather cap or other instance where a filler neck is required. Diameter...

Spark Plug Boots Black 1/16

Rubber boots ready to use as is, for straight boots, or cut them and glue at a 90 degree angle for angled boots.Use in combination with your choice of color Pro Tech Spark Plug Wire.Each pack contains 8 black boots, by Pro Tech.

Blown Engine Fuel Plumbing Schematics

NEW AND UPDATED All the information you need to plumb the fuel lines on an early or modern blown engine. A few lines can be changed to represent older blown engines.Covers all the fuel lines from the fuel cell to the injectors, listed in 4 different...

Large Detailing Wire

Large gauge detailing wire for ignition items, batteries and other items that have large electrical loads. Available in Black, Red, Blue and Yellow. One package contains 3' x .018" diameter wire. Specify color.

Larger Detailing Wire or 1/16 Spark Plug Wire

This black wire can be used for a large gauge electrical wire for 1/25 and 1/16 scales and it's also used for 1/16 scale spark plug wire. This has a solid copper core and will maintain its shape when formed. One package contains 3' of black wire, .024"...

M&H Racemaster Drag Slicks 1/16

M&H Racemaster Drag Slicks. Raised 'M&H Racemaster' on sidewall. These are a hard resin and do not have a lot of room for play with wheel sizes. Tire Measurements: Width 1.00",  25.4mmDiameter. 2.00", 50.8mmWheel opening 1...