Shop by Manufacturer

5-Point Racing Harness 1/25

Pro Tech's 5-Point Racing Harness with photoetched buckles and ready to use harness material.                               Pro Tech's own design makes it easy to assemble,...

License Plate Frame Set 1/25

Photoetched scale state license plate frames for added realism.   Also, see the state license plates and performance license plates.   One set of 8 photoetched license plate frames, by Pro Tech.

Performance License Plate Set 1/25

Performance license plates for added realism.   Plates included are:   Chevrolet USA-1 Chrysler Dodge Ford Motorsports Ford Lincoln Mercury Mercury Mopar Mustang Plymouth Today's Chevrolet   Also, see the other state license plates along...

Detailing Wire .007"

Very small wire to be used for ignition wiring, computer connections, gauges, etc.Available in the following colors:BlackRedBlueYellowOne package of wire .007" x 3', by Pro Tech.

Heater Hose 1/25

This copper core wire is used as a small heater hose or other transfer hose. The copper core will hold its shape when formed into place.  Cut the outer skin back, at the ends, just enough to leave a stub to insert into a drilled hole.Use hex...

Drag Racing Parachute 1/16

Detailed Drag parachute.One per package.Resin

Carburetor Fuel Junction Block 1/16

For your single or dual carburetor setups.  Made with molded-on fittings.Use .035 Braided Lines and Fittings and large T fitting. Each package contains 1 Fuel Junction Block, by Pro Tech. Resin cast

Blown Engine Fuel Plumbing Schematics

NEW AND UPDATED All the information you need to plumb the fuel lines on an early or modern blown engine. A few lines can be changed to represent older blown engines.Covers all the fuel lines from the fuel cell to the injectors, listed in 4 different...

Large Detailing Wire

Large gauge detailing wire for ignition items, batteries and other items that have large electrical loads. Available in Black, Red, Blue and Yellow. One package contains 3' x .018" diameter wire. Specify color.

5-Point Racing Harness 1/16

5-Point Racing Harness with metal cast buckles and ready to use harness material.Not your flat photo-etched hardware. This is cast for 3D texture and detail. Pro Tech's own design makes it easy to assemble, realistic and beautiful to look at. Can be...

Drag Slicks, 14x32x15 1/25

These Drag Slicks equal a scale 14x32-15 tire.  The tread width equals 14" and the overall width, with sidewalls equals 18". To determine if these will fit your needs, here are the actual dimension:Width including Sidewall = .75"Tread Width = ...

Oil Filters Decal Sheet 1/25

Here is a small sheet of decals with oil filters.  Includes 2 different FRAM logos, WIX, Motorcraft and more. There are enough decals on this small sheet for several cars. Product photo does not necessarily reflect the actual sheet you receive...

Nitrous & Fire Bottles and Ignition Boxes Decal Sheet 1/25

Need N0S or MSD ignition box decals but don't want to pay for a sheet of decals you will never use? Here is a small sheet of decals specifically for labels on Nitrous Bottles, Fire Bottles and Ignition Boxes. This is cut from a larger decal sheet which...

Hood Pin Set 1/25

One-piece (pin and plate) hood pins that are photoetched. Contains 12 photoetched hood pins per pack, by Pro Tech.

4-Hole Carbon Fiber Hat 1/25

A 4-Hole compact Injector Hat.  This is slightly raised and has 4 square butterflies. Molded in one piece. Contains 1 resin hat.

Vertex Magneto, Aluminum, Pre-Wired 1/25

A machined aluminum Vertex magneto for those early racing engines.The color in the item photo does not reflect the actual color.  Select your choice from the color swatches.Choose your color of spark plug wire...

Pre-Wired Distributor 1/25

Here's a machined aluminum distributor body with your color choice of spark plug wire already installed.Drill a hole in your block and insert this distributor. Route the wires to the spark plugs and don't forget the Pro Tech Spark Plug Boots, for even...

Battery (pair) 1/25

A pair resin batteries to add detail for the trunk or the engine bay. Dress them up with manufacturer's decals found here and battery connectors here.   For multiple battery connections in Parallel or Series, look here.     Contains 2...

Fuel Cell Set 1/25

A pair of 3D-printed fuel cells with photo etched ring and strap material. Includes:Two 3D-printed fuel cellsPhoto etch rings and latch detailThe fuel cells have recesses for the PE detail to seat correctly 3D-printed and photo etched, 1/25 scale...

Front Runner Tires 1/25

Front drag tire patterned after Goodyear Frontrunner style. Designed to be direct fit for R/M style drag front wheels. Dimensions: 1" OD.65" (21/32")  ID.25" wide Click here for a free downloadable sizing and fitment table for tires and wheels...

Wrinkle Wall Drag Slicks, 1/25

Current style Drag Slicks with a wrinkled sidewall.  Dimensions are listed below to see if they fit your needs. Each side of these tires will accept a different size wheel. Tire Measurements: Width .60",  15.25mmWheel opening .660", 16...

Ferrule Fittings for Braided, Soft, Hard LInes -Brass

Perfect for simulating crimp-type end-of-line fittings on Blower injector lines, Injector Hat injector lines or carb fittings. Can also be used as carburetor 'boosters'.  The photo above shows injector lines using Size A ferrules and .020"...

Gauges, Hood Pins, Dzus Fasteners & Brake Calipers Decal Sheet 1/25

Here is a small sheet of decals with digital and analog gauges, hood pins & Dzus fasteners and labels for brake calipers. There are enough decals on this sheet for a few cars. The product photo shown is a representation and may not look exactly...

Soft Line - Hose .020", .5mm OD

This soft line equals the following equivalent 1:1 size at each scale.1/25 scale = 1/2"1/16 scale = 1/4" or 5/16"1/12 scale =1/4"1/8 scale  = 1/8"Typical uses are small oil, vacuum and fuel lines, especially fuel & nitrous delivery at the the...

Oil Filters 1/25

Oil filters made of cast metal.This is a standalone filter. If you need a dual remote oil filter, see Pro Tech's product listed elsewhere here. Each package contains 8 metal cast pieces, by Pro Tech.

Spark Plug Wire Looms, Photoetched 1/25

These wire looms will keep your spark plug wires separated. This will give you an organized look and it makes it easier to form your wires where you want them.  Used on all drag cars or street vehicles.There are enough wire looms here for many cars...

Parachute Kit 1/25

This is the ultimate in a 1/25 scale drag chute - Contains an inner resin parachute core with an outer textured material to simulate the actual parachute jacket material.  Don't rely on flat black paint anymore. Color the material any color you want...

Spark Plug or Large Detailing Wire 1/25

Choose a color for your spark plug wires.This can also be used for large detailing wire, if the other Pro Tech wire choices aren't large enough.Available colors:BlackRedBlueYellowOrangeGrayOne length of wire .018" x 3', by Pro Tech.Specify color.

Molded Blower Belt with Pulleys 1/25

A more detailed blower belt set than found in kits. The belt shows cogs on the inside and bolt heads are found on the pulleys. Also has the blower pulley, crank pulley and idler pulley molded in..   Blower pulley to Crank pulley center-to-center...

Drag Slicks,17x36x16 1/25

These Drag Slicks equal a scale 17x36-16 tire.  This is representative of a current Pro Mod, FC or TF drag slick. Dimensions:Overall Width = .85"Diameter = 1.46"Tread Width = .70"Wheel Opening =.715" The tire ID is designed to work with earlier...

Nostalgia Drag Racing Contingency Decal Sheet #3 1/25

Nostaglia style Drag Racing Contingency decal sheet.Includes many sponsors' and manufacturers' names from the past Crower, Gumout, Pennzoil, Howard's Cams, VHT, Accel, Holley and many more.One decal sheet by SLIXX Decals, 1/25 scale.

Spark Plug Boots - Colors 1/25

Boots for spark pugs or other electrical wiring in 4 colors.Use in combination with your choice of Pro Tech Spark Plug Wire. Each pack contains 8 boots, 1/25 scale, by Teds Modeling. CHOOSE COLOR

Spark Plug Boots Black 1/25

Rubber boots ready to use as is, for straight boots, or cut them and glue at a 90 degree angle for angled boots.Use in combination with your choice of color Pro Tech Spark Plug Wire.Each pack contains 8 black boots, by Pro Tech.

Tire Valve Stems 1/25

Add another element of detail to your wheels.A set of machined aluminum tire valve stems. Photo of Tire Valve Stems with .025 Hex Fittings for the lug nuts. Use .025 Evergreen rod for the studs. See the How-To article on detailing wheels:...

Supercharger Pulley Set 1/25

Three cast-metal pulleys and blower belt materail   3-pieces cast-metal and blower belt material by Pro Tech.

Aero II Pro Stock Hood Scoop, 1/25

A Rectangular Opening Pro Stock Hood Scoop. It's designed to rest against the windshield and may have to be adjusted to fit your windshield angle. See also a longer version of this hood scoop here. Molded in one piece. Contains 1 resin scoop, 1/25...