Shop by Manufacturer

Lever Style Safety Harness Set 1/16

Here is a set of highly detailed lever-lock safety harness hardware. Belt material is not included. Here is a photo of this hardware installed in a '60's short track racer by Matt Zimmerman. Assembly required. Photo etched pieces are made from...

4-Link Suspension Bracket Kit 1/16

This 4-link bracket set includes eight brackets, enough to build one car.  They are patterned after a popular 1:1 bracket.  The hole diameters in the housing brackets are .188", so they can be drilled out to the diameter of your axle housing...

Slotted Rotor 4-Piece Set 1/16

Slotted, 4-rotor set - front and rear. Front rotors equal a scale diameter of 10". Rrear rotors equal a scale 11.75" @ 1/16 scale.   Photo of a real slotted rotor with dual calipers. For a set of drilled rotors check here, or for drilled...

Drilled Rotor 4-Piece Set 1/16

Drilled, 4-rotor set. Front rotors equal a scale diameter of 10". Rrear rotors equal a scale 11.75" @ 1/16 scale. For rear rotors only, click here.   Four pieces, photo etched .015" nickel-silver plate, 1/16 scale.

Drilled Rotor Pair, Large/Rear 1/16

Drilled, large 2-rotor set - These represent a scale diameter of 11.75" @ 1/16 scale. These would be used as rear rotors.  For a set of front and rear rotors, click here.   One pair, photo etched .015" nickel-silver plate, 1/16 scale.

Injector Butterfly Set for Competition Resins Injector Hat 1/16

These Butterflies are finely detailed showing the cross shaft and screws holes for each butterfly disc. They are made to fit the Competition Resin's '70's Ribbed injector hat.  They measure .215" diameter and may fit your...

Motorwheel Pro Stock Wheels Front & Rear 1/25

A set of four Motorwheel P/S Racing Wheels - front and rear. Contains 2 pairs resin wheels, 1/25 scale.

Dragster or Fuel Altered Front Tires 1/16

Skinny front tires for wire or spoked wheels, as found on dragsters and altered. Measurements: 1" OD 0.7" ID These tires fit the Comp Resins 12-spoke wheels found here. Contains 1 pair rubber-like tires.

Pro Mod / Funny Car / Pro Stock Rear Wing 1/25

Includes main horizontal wing, sides and support rods. This wing can be made to fit many different race classes.   Here are some examples of what can be done.     Resin, 1/25 scale

Dual Nitrous , O2, Fire or Air Bottle Pair 1/25

Here are a pair of bottles that can be used for nitrous, fire, compressed air, oxygen, etc. Mount them in the interior, at the rear or ahead of the engine. Add a NOS decal found here, if this is the intended use for these bottles.  The 'small' size...

Cragar Super Trick 8-hole Rear Wheels 1/16

Cragar Super Trick, 8-hole rear drag racing wheels. Fits Revell tires...

Pro Stock / Super Stock Drag Slicks 1/25

Drag Slicks for your Pro Stock, Super Stock or other race car.  Dimensions are listed below to see if they fit your needs. Each side of these tires will accept a different size wheel.                 ...

Lenco Transmission 4-Speed/Reverse, Manual Shift 1/25

This is a complete Lenco transmission configured for 4-speeds with reverse. It is a one-piece unit including 3D-printed shifter levers (the shifter levers are really small and easy to loose). The front section contains gears 1 and 2 and is...

Door Lever Set - Doorslammer or Street Machine 1/16

Door car levers to detail that race car or street machine interior.  These levers can be used in any type of build. They can be used for interior or exterior handles as well as parachute or other release leavers. Photo etched .010...

Injector Butterfly Set for Competition Resins Shotgun Hat 1/16

These Butterflies are finely detailed showing the cross shaft and screws holes for each butterfly disc. They are made to fit the Competition Resins 2-Hole Shotgun injector hat (part #148).  Click here to see the 1/16 injector hat...

Injector Butterfly Set for Competition Resins Enderle Hat 1/16

These Butterflies are finely detailed showing the cross shaft and screws holes for each butterfly disc. They are made to fit the Competition Resins Enderle injector hat (part #035).  Click here to see the 1/16 injector hat...

4-Link Pro Mod Suspension Kit (also fits Dana) 1/25

This kit represents the current heavy duty style of 4-link kits found on high horsepower Pro Mod drag cars. Also included in this kit is anti-roll bar linkage and arms. No torsion bar/tube is included and must be scratch built. Included are four .050"...

Lenco Shifter Lever Set 1/25

You need a set of these Lenco shifters for your Pro Mod or other drag car.  Adds realism and detail to your build. Contains set of levers, brackets, linkage and instructions.. Make sure you click on the product photo above, to enlarge it, to...

Pedal Set for FC, PM or Door Slammer 1/25

You need a set of these pedels to complete that racing interior and sdd realism and detail to your build. Enough for two cars or more, depending on how many pedals you need.                Contains TWO...

Hand Brake-Parachute Lever Set 1/25

A pair of levers for a Hand Brake to add detail to your cockpit. Enough for two builds. Contains two levers and hand grips plus 2-sizes of additional small levers for a parachute release or other. Photo etched, 1/25 scale.

Dragster Accelerator Pedal Set 1/16

These dragster pedals replicate modern tubular constructed accelerator pedals. They incorporate a safety return loop on both the top and side. Choose whichever one you wish and remove the other. Photo etched, 1/16 scale.

Pedal Set for FC, PM or Door Slammer 1/16

You need a set of these pedels to complete that racing interior and sdd realism and detail to your build.   Contains one each: Accelerator pedal Brake pedal Clutch pedal Pedal foot pads Make sure you click on the photo, to enlarge...

Lenco Shifter Lever Set 1/16

You need a set of these Lenco shifters for your Pro Mod or other drag car.  Adds realism and detail to your build. Contains set of levers and will work with the TDR or Flash Point Lenco transmissions. Make sure you click on the photo, to enlarge...

Hand Brake Levers for for PM or TF 1/16

A set of Hand Brake Levers for your Dragster or Funny Car.  Adds realism and detail to your build. Contains two brake levers with additional hand grips. Place a small piece of styrene between the lever grip and added grip for thickness. Photo...

Small Block Engine Crank Trigger 1/16

Here is a Crank Trigger kit, for a small block engine and especially for the small block Chevy. Includes crank trigger wheel, sensor mount and adjustable sensor mounting bracket. A crank triggered ignition system can make more horsepower than a...

Big Block Engine Crank Trigger 1/16

Here is a Crank Trigger kit, for the a block engine and especially for the big block Chevy. Includes crank trigger wheel, sensor mount and adjustable sensor mounting bracket. A crank triggered ignition system can make more horsepower than a distributor...

Oval Fender Exhaust Bezels Pro Mod, etc 1/16

These bezels are designed to replicate the bezels used on modern Pro Mod and other cars where the exhaust exits the fender well, just behind the front wheel. These are oval, but round bezels are also available for a straight exhaust exit. Photo Etched,...

Round Fender Exhaust Bezels Pro Mod, etc 1/16

These bezels are designed to replicate the bezels used on modern Pro Mod and other cars where the exhaust exits the fender well, just behind the front wheel. The inside diameter is .25". These are round, but oval bezels are also available for an angled...

Round Window Bezels Pro Mod, etc 1/16

These bezels are designed to replicate the window bezels used on modern Pro Mod and other cars for ventilation and pressure equalization. Photo Etched, (2 pr) 

23" Holli's (Halibrand) Wheels & Tires (2 pair) 1/24-1/25

A set of four 23", deep dish, chrome Pegasus wheels with low profile tires. Sidewall and tread width is .45" (29/64") Like the wheels but don't want low profile tires?  Take these tires off and replace with other tires. By Pegasus, 1/24 scale...

1471 Kobelco Blower 1/25

A 1471 Kobelco Blower in one-piece resin.The detail is quite good and the bolts are sharp. This is a standalone blower - pulleys or other components are not included. Check out this photo for an idea of which blower you need. Contains 1 resin blower.

Arden Heads with Valve Covers 1/25

For that Flathead engine - a pair of Arden heads with valve covers. The spark plug holes can be easily drilled. You can't tell by the photo, but ARDEN is spelled across the face. Contains 2 resin pieces.

Pro Stock Late Model Valve Covers 1/25

A pair of Pro Stock valve covers with a flat face. Contains 2 resin pieces.

Milodon Valve Covers 1/25

A pair of really nice Milodon valve covers with spark plug holes already drilled. These valve covers have horizontal grooves running lengthwise. They fit on a BBC engine. Contains 2 resin pieces.

Dual Plug HEMI Valve Covers 1/25

A pair of HEMI valve covers with dual spark plug holes already drilled. Contains 2 resin pieces.

Street Rod Gauges Set #1, Black 1/25

Enough photoetched trims and BLACK gauge faces for four cars. This will add detail to your interior.These gauges are popular in '30 - '34 Street Rods and Roadsters with flat dash boards. They are typically mounted in the center of the dash or over...