Drive Train & Chassis

Central Frame Rail 1/24-1/25

  Want to build your own chassis to fit in that drag racing body? This central frame rail is a vital component containing the cockpit area.This is a one-piece item and doesn't need any assembly. This section can be used with the Forward Frame Rail...

Gray Cable .010", .25mm Dia

This looks like a stainless steel line, but it's a small gauge stainless steel wire wrapped in a gray nylon jacket. This is ideal for a throttle or parachute release cable where a steel cable is housed in a jacket. The wire core is springy and doesn't...

Disc Brakes with Calipers, Chrome (2 pair) 1/24-1/25

A set of four chrome plated disc brakes with molded-in calipers. The discs are drilled and represent a scale 19". Four resin discs/calipers, chrome plated, 1/24-1/25 scale, by Pegasus, .    

BBC Offset Motor Plate 1/25

A more accurate motor plate than found in a kit. It is offset for those cars with an off-center driveline.While this motor plate is copied after the one used in the Revell Pro-Sportsman kits, it can be used in any build with possible modification.It is...

Power Steering Pump w/ Pulley 1/25

Here's an item that will detail that engine bay - a power steering pump.  It's modeled after the popular Saginaw pump. Includes an aluminum pulley. Check here for a high pressure hose and here for a rack and pinion set.   One piece resin body...

Wishbone Kit, Lower A-Arm 1/25

These are perfect with Futurattraction's Front Strut kit for the lower A-Arms.These will fit inside 1/16" OD (with an ID of .033") or .042" OD stainless steel tubing (included). Includes:2 - Wishbones2 - Washers - .010" thick4 - Spacers .015" thick1 -...

Rear Tube Frame/Clip .900" Wide 1/25

Here's  a round-tube rear frame clip ready to install.  It's 3D printed. Dimensions are:Frame width = .900" (about 29/32", 22.9mm)Frame tube diameter = .080"Cross member diameter = .080"Overall length = 2.55" Two other frame clip widths are...

Rear Tube Frame/Clip .700" Wide 1/25

Here's  a round-tube rear frame clip ready to install.  It's 3D printed in FUD material (see below). Dimensions are:Frame width = .700" (about 45/64", 17.8mm)Frame tube diameter = .080"Cross member diameter = .063"Overall length = 2.55" Two...

4-Link Set for Rear Tube Frame/Clip 1/25

This 4-Link kit fits narrowed OEM-style 9-inch Ford housings.  Designed to fit RTF (round tube frame) and FRK (mandrel bent frame rail kits) found elsewhere here in three different diameter sizes.   Includes:2 - Chassis brackets2 - ...

Rear Tube Frame/Clip .800" Wide 1/25

A round-tube rear frame clip ready to install.  It's 3D printed in FUD material. Dimensions are:Frame width = .800"Frame tube diameter = .080"Cross member diameter = .080"Overall length = 2.55" Two other frame clips widths are available in .700"...

Weld Beads 3D - Arc 1/25 - 1/24

Weld beads in 3D by Archer Surface Details. Use them wherever welds would be found, like: headers, intake manifolds/air boxes, frames, roll bars and the list goes on. These arc-weld beads are the typical hand-held welds you'd make yourself. ...

Coil Spring .375" x .125" (pair) 1/25

These springs are used on Fururattraction's Coil Over Shock kits, but can be used in any suspension system that requires the dimensions below. The ends are ground flat.    Total height is .375" Outside diameter is .125" Wire diameter...

Coil Spring .250" x .125" (pair) 1/25

These springs are used on Fururattraction's Front Strut kits, but can be used in any suspension system that requires the dimensions below. The ends are ground flat.    Total height is .250" Outside diameter is .125" Wire diameter is ...

Brake Kit, Drilled Rotor - Rear 1/25

A detailed complete rear end brake set. This drilled rotor set is designed to work with a .063" diameter kit axle but allows the use of separate calipers and PE brackets, for more realism. Kit includes: 3D calipers (2 pieces per...

Sportsman 4-Link Suspension Kit for Revell 1/25

4-Link multi-media kit replicates styrene 4-link in Revell top sportsman kit. Fits Revell kit rear ends or rear ends with .125" OD axle housing with no back brace. Kit includes chassis and rear end housing brackets, four .050" OD stainless steel...

Dana 60 Rear End 1/25

A hard-core Dana rear end.      Photo of real Dana 60 by Moser                 Photo of a real Dana 60 by Strange     Contains 1 resin piece, 1/25 scale

GM 700R Transmission 1/25

A General Motors trick 700R automatic transmission. Contains 1 resin transmission, 1/25 scale

Dual Nitrous , O2, Fire or Air Bottle Pair 1/25

Here are a pair of bottles that can be used for nitrous, fire, compressed air, oxygen, etc. Mount them in the interior, at the rear or ahead of the engine. Add a NOS decal found here, if this is the intended use for these bottles.  The 'small' size...

Lenco Transmission 4-Speed/Reverse, Manual Shift 1/25

This is a complete Lenco transmission configured for 4-speeds with reverse. It is a one-piece unit including 3D-printed shifter levers (the shifter levers are really small and easy to loose). The front section contains gears 1 and 2 and is...

4-Link Pro Mod Suspension Kit (also fits Dana) 1/25

This kit represents the current heavy duty style of 4-link kits found on high horsepower Pro Mod drag cars. Also included in this kit is anti-roll bar linkage and arms. No torsion bar/tube is included and must be scratch built. Included are four .050"...

Lenco Shifter Lever Set 1/25

You need a set of these Lenco shifters for your Pro Mod or other drag car.  Adds realism and detail to your build. Contains set of levers, brackets, linkage and instructions.. Make sure you click on the product photo above, to enlarge it, to...

Pedal Set for FC, PM or Door Slammer 1/25

You need a set of these pedels to complete that racing interior and sdd realism and detail to your build. Enough for two cars or more, depending on how many pedals you need.                Contains TWO...

Hand Brake-Parachute Lever Set 1/25

A pair of levers for a Hand Brake to add detail to your cockpit. Enough for two builds. Contains two levers and hand grips plus 2-sizes of additional small levers for a parachute release or other. Photo etched, 1/25 scale.

Soft Line - Hose .157", 4mm OD & Roll Bar Padding in 1/16

This is a large, soft, rubber tubing (hollow) that is easily configured to the space you have. It's able to bend at a sharp angle without kinking or folding.I do not have Hex Fittings for this soft line. This soft line equals the following equivalent 1:1...

Brake or Fuel Line .014, .35mm Dia

Use this for 1/25 scale brake lines and injector lines.           This aluminum hard line equals the following equivalent 1:1 size at each scale.1/25 scale = 5/16"1/16 scale = 3/16"1/12 scale = N/A1/8 scale  =  N/AUse...

Fuel or Brake Hard Line .020, .52mm Dia

This solid aluminum line is soft to bend and will not kink, even at tight angles. It straightens out easily and will conform to any shape you want.This aluminum 'hard' line equals the following equivalent 1:1 size at each scale.1/25 scale = 1/2"1/16...