1/16 Scale

Drag Racing Goody Decal Sheet 1/16

1/16 scale Drag Racing GOODY decal sheet. Includes many sponsors' and manufacturers' names. Nitrous labels, bellhousing logos, fire bottle labels, MSD logos, NHRA & IHRA decals, blower belt and valve cover decals plus lots more.New from SLIXX Decals...

Funny Car Grill & Headlights Decal Sheet 1/16

1/16 scale grille and headlight decals for current and nostalgia drag racing cars.One sheet.SLIXX Decals, 1/16 scale

Tee Fitting, Large

This is a large inline fitting for braided lines, hard lines or hoses.  Anywhere you have a split.Typical uses are dual feed carburetors, tunnel ram, oil lines and brake lines.Use Pro Tech .035 Braided Line and matching Fittings. Each package...

Tee Fitting, Small

This is an inline fitting for braided lines, hard lines or hoses.Typical uses are splits for carburetor fuel lines and brake lines.Use Pro Tech .025 Braided Line and matching Fittings. Each package contains one T fitting, by Pro Tech. Metal Cast

Detailing Wire .007"

Very small wire to be used for ignition wiring, computer connections, gauges, etc.Available in the following colors:BlackRedBlueYellowOne package of wire .007" x 3', by Pro Tech.

Barry Grant DEMON 4bbl Carburetor 1/16

Detailed Barry Grant 4bbl CarburetorWith single or dual carbs, you'll need Pro Tech's 1/16 scale Fuel Junction Block.Also see the Braided Lines, Hard Lines, Soft Lines and Fittings along with the T fitting to split the fuel line to each carb. One...

Holley Dominator 4bbl Carburetor 1/16

Detailed Holly Dominator 4bbl CarburetorWith single or dual carbs, you'll need Pro Tech's Fuel Junction Block.Also see the Braided Lines, Hard Lines, Soft Lines and Fittings along with the T fitting to split the fuel line to each carb. One per...

Drag Racing Full Face Helmet 1/16

Detailed Full Face Helmet. Ready for your custom paint design.  Looks right at home on the cockpit seat or the hood of that Pro Mod car. One per package. Resin

Drag Racing Parachute 1/16

Detailed Drag parachute.One per package.Resin

Barrel Valve 1/16

A barrel valve is located on the left side of a supercharged engine injector hat. The fuel input is via a braided line from the fuel pump and 2 outlet braided lines go to 2 fuel junction blocks (see ENGINE DETAILING).Designed for Pro Tech .035 Braided...

Dual Remote Oil Filter 1/16

Each package contains 1 adapter and 2 oil filters.   See the Braided Lines and Fittings to complete the plumbing of the oil lines. Adapter is metal cast and can be polished.  Filters are machined aluminum   

Aluminum Oil Filter 1/16

Each package contains 1 filter. Machined aluminum  

MSD 7 Ignition Box 1/16

Each package contains 1 MSD 7 ignition box. See 'Detailing Wire, Small' to enhance this item.Resin 

MSD 6 Ignition Box 1/16

Each package contains 1 MSD 6 ignition box. The casting of this box shows the ribs and area for the MSD logo. The photo shows two Pro Tech MSD boxes with MSD labels copied from an automotive magazine and reduced. These are not included with the MSD 6...

Blown Engine Fuel Injection Block 1/16

Fuel Injection Block for supercharged engines. This is the fuel block that is located behind the injector hat and behind the blower which feeds the manifold. Use Pro Tech?s .035 Braided Line along with the corresponding fittings for the fuel feed line to...

Carburetor Fuel Junction Block 1/16

For your single or dual carburetor setups.  Made with molded-on fittings.Use .035 Braided Lines and Fittings and large T fitting. Each package contains 1 Fuel Junction Block, by Pro Tech. Resin cast

Aluminum Ignition Coil 1/16

Machined aluminum ignition coil with rubber boot.Use with your color choice of Pro Tech Spark Plug Cable.

Distributor Kit 1/16

Resin distributor, shaft and boot material. The cap has 'starter' holes to drill out and insert the spark plug boot which is cut from the included material. Refer to the photo showing a completed distributor. Assembly and painting are not included...

Throttle Linkage 1/16

Whether it's a blown engine, injected or carbureted, these photoetched pieces will detail your throttle linkage. For the metal linkage that fit into the holes, use the .014 and .020 aluminum lines.  These are stiff enough to hold...

Rod Ends/Link/Heim Kit 1/16

Cast metal parts for your suspension or throttle linkage detail.  Can be used for heim joints/rod ends in suspension areas like a 4-link rear end, panard bar or front radius rods. Use in combination with Pro Tech's Throttle Linkage kit for a...

Roll Bar Padding 1/16

Rubber tubing for roll bars.Can also be used for other larger water/coolant hoses.At 1/16 scale, this would be equal to 1.5" ID and 3.5" OD.At 1/12 scale, this would be equal to 1.25". ID and 2.5" OD.Black.

Mallory/MSD Ignition Coil 1/16

Modeled after a Mallory Ignition Coil. Also looks very similar to a MSD Ignition Coil. Photo of completed piece is for reference only. Painting, wires and decals are not included. Each package contains 1 coil. Resin 

Aluminum Gas Cap 1/16

Excellent detail for your race car fuel cell, hot rod Moon tank and other tanks like an oil tank on a Funny Car, Pro Mod or Dragster.Can also be used for a radiator cap, engine oil breather cap or other instance where a filler neck is required. Diameter...

Spark Plug Boots Black 1/16

Rubber boots ready to use as is, for straight boots, or cut them and glue at a 90 degree angle for angled boots.Use in combination with your choice of color Pro Tech Spark Plug Wire.Each pack contains 8 black boots, by Pro Tech.

Blown Engine Fuel Plumbing Schematics

NEW AND UPDATED All the information you need to plumb the fuel lines on an early or modern blown engine. A few lines can be changed to represent older blown engines.Covers all the fuel lines from the fuel cell to the injectors, listed in 4 different...

Large Detailing Wire

Large gauge detailing wire for ignition items, batteries and other items that have large electrical loads. Available in Black, Red, Blue and Yellow. One package contains 3' x .018" diameter wire. Specify color.

Larger Detailing Wire or 1/16 Spark Plug Wire

This black wire can be used for a large gauge electrical wire for 1/25 and 1/16 scales and it's also used for 1/16 scale spark plug wire. This has a solid copper core and will maintain its shape when formed. One package contains 3' of black wire, .024"...

M&H Racemaster Drag Slicks 1/16

M&H Racemaster Drag Slicks. Raised 'M&H Racemaster' on sidewall. These are a hard resin and do not have a lot of room for play with wheel sizes. Tire Measurements: Width 1.00",  25.4mmDiameter. 2.00", 50.8mmWheel opening 1...

Late Model Enderle Injector Hat 1/16

An Enderle 3-port injector hat.   See also, photo eteched butterfly set to fit this injector.   Resin, 1/16 scale.

671 GMC Blower 1/16

A 671 blower for early dragsters or for a street machine.Blower pulley is attached to the front plate.The detail is quite good and the bolts are sharp. Check out this photo for an idea of which blower you need. Contains 2 resin pieces.

5-Point Racing Harness 1/16

5-Point Racing Harness with metal cast buckles and ready to use harness material.Not your flat photo-etched hardware. This is cast for 3D texture and detail. Pro Tech's own design makes it easy to assemble, realistic and beautiful to look at. Can be...