Shop by Manufacturer

Valve Cover T-Bolts, Photoetched 1/25

Add realism to your engine bay with these Valve Cover T-Bolts. They're long valve cover bolts that have a T shape at the top.There are enough valve cover bolts here for a few cars. One set photoetched, by Pro Tech.

License Plate Frame Set 1/43

Photoetched scale state license plate frames for added realism. NOTE THIS IS 1/43 SCALE ONLY Also, see the state license plates and performance license plates. One set of 8 photoetched license plate frames, by Pro Tech.

State License Plate Set 1/25

State license plates for added realism.   Plates included are: ArizonaCanadaColoradoFloridaIllinoisMichiganMarylandNew JerseyNew YorkTennessee Also, see the license plate frames.   One set of 16 plates printed on paper, by Pro Tech.

Radiator or Heater Hose, .070" OD

This solid core wire is used as a 1-3/4" radiator hose or other larger transfer hose at 1/25 scale.  At 1/16 scale it equals a 1" diameter hose, which is closer to a heater hose. It has an outside diameter of .070" It will hold its shape when...

Barry Grant DEMON 4bbl Carburetor 1/16

Detailed Barry Grant 4bbl CarburetorWith single or dual carbs, you'll need Pro Tech's 1/16 scale Fuel Junction Block.Also see the Braided Lines, Hard Lines, Soft Lines and Fittings along with the T fitting to split the fuel line to each carb. One...

Holley Dominator 4bbl Carburetor 1/16

Detailed Holly Dominator 4bbl CarburetorWith single or dual carbs, you'll need Pro Tech's Fuel Junction Block.Also see the Braided Lines, Hard Lines, Soft Lines and Fittings along with the T fitting to split the fuel line to each carb. One per...

Drag Racing Full Face Helmet 1/16

Detailed Full Face Helmet. Ready for your custom paint design.  Looks right at home on the cockpit seat or the hood of that Pro Mod car. One per package. Resin

Barrel Valve 1/16

A barrel valve is located on the left side of a supercharged engine injector hat. The fuel input is via a braided line from the fuel pump and 2 outlet braided lines go to 2 fuel junction blocks (see ENGINE DETAILING).Designed for Pro Tech .035 Braided...

Dual Remote Oil Filter 1/16

Each package contains 1 adapter and 2 oil filters.   See the Braided Lines and Fittings to complete the plumbing of the oil lines. Adapter is metal cast and can be polished.  Filters are machined aluminum   

Aluminum Oil Filter 1/16

Each package contains 1 filter. Machined aluminum  

MSD 7 Ignition Box 1/16

Each package contains 1 MSD 7 ignition box. See 'Detailing Wire, Small' to enhance this item.Resin 

MSD 6 Ignition Box 1/16

Each package contains 1 MSD 6 ignition box. The casting of this box shows the ribs and area for the MSD logo. The photo shows two Pro Tech MSD boxes with MSD labels copied from an automotive magazine and reduced. These are not included with the MSD 6...

Throttle Linkage 1/16

Whether it's a blown engine, injected or carbureted, these photoetched pieces will detail your throttle linkage. For the metal linkage that fit into the holes, use the .014 and .020 aluminum lines.  These are stiff enough to hold...

Rod Ends/Link/Heim Kit 1/16

Cast metal parts for your suspension or throttle linkage detail.  Can be used for heim joints/rod ends in suspension areas like a 4-link rear end, panard bar or front radius rods. Use in combination with Pro Tech's Throttle Linkage kit for a...

Roll Bar Padding 1/16

Rubber tubing for roll bars.Can also be used for other larger water/coolant hoses.At 1/16 scale, this would be equal to 1.5" ID and 3.5" OD.At 1/12 scale, this would be equal to 1.25". ID and 2.5" OD.Black.

Mallory/MSD Ignition Coil 1/16

Modeled after a Mallory Ignition Coil. Also looks very similar to a MSD Ignition Coil. Photo of completed piece is for reference only. Painting, wires and decals are not included. Each package contains 1 coil. Resin 

Aluminum Gas Cap 1/16

Excellent detail for your race car fuel cell, hot rod Moon tank and other tanks like an oil tank on a Funny Car, Pro Mod or Dragster.Can also be used for a radiator cap, engine oil breather cap or other instance where a filler neck is required. Diameter...

Late Model Enderle Injector Hat 1/16

An Enderle 3-port injector hat.   See also, photo eteched butterfly set to fit this injector.   Resin, 1/16 scale.