Fuel Management

Soft Line - Red .008" OD

This is the smallest red soft line I have. It is almost a human hair thick. It is flexible, yet stiff enough to stand up without falling over and it is dark red.  It is nylon and can bend at a fairly sharp angle without kinking.See Size A1...

Soft Line - Red .012", .30mm OD

This is a small, solid, flexible, deep red line.  It can bend at a fairly sharp angle without kinking.See Size A1 Ferrules for this soft line. This soft line equals the following equivalent 1:1 size at each scale.1/25 scale = 5/16"1/16 scale...

3D-Printed Demon Carburetor 1/25

Highly detailed Holley Street/Strip 4-bbl Carburetor.The photos of the carb show it on the top of Micro Scale Set bottle. Dimensions: Overall length (float bowl to float bowl) - .540" Carb diameter (for velocity stacks) - .290". The velocity stacks by...

Blower Restraint Plate, 1/25

This restraint plate sits under the blower and restraint straps would fasten to the slots and go over the blower to hold it down in the event it would blow up. It is universal to all blowers. This photo etched piece is etched out of .006" nickel-silver...

RBS Square 4-Hole Hat with Butterflys, 1/25

This is a CAD designed replica of an RBS Square 4-Hole Injector Hat, in 1/25 scale. The intake openings are hollowed out. Small holes across the front openings are provided for a rod to connect the butterflys to your throttle linkage and barrel valve...

Injector Stacks, Tall 1/24, 1/25

A set of eight machined aluminum tall, flared, injector stacks. Hilborn Style Injector Stacks 5/32 x 3/32 x 1/2. Eight aluminum stacks by Parts by Parks, 1/24-1/25 scale.

Large, 3-Hole Carbon Fiber Hat 1/24

A three round-hole, tall Injector Hat similar to what you find on TF and PM cars. This is normally a carbon fiber hat in real life.  Search for Carbon Fiber decals in the search box at the top right of this window. Molded in one piece. Contains 1...

3D-Printed 'Street' 4bbl Carburetor 1/25

Highly detailed Holley Street 4-bbl Carburetor with a choke plate in the closed position.With single or dual carbs, you'll need a Fuel Junction Block (see 1/25 SCALE/ENGINE RELATED/FUEL MANAGEMENT). Also see the Braided Lines, Hard Lines, Soft Lines and...

3D-Printed 4bbl Carburetor 1/25

Highly detailed Holley Street/Strip 4-bbl Carburetor.With single or dual carbs, you'll need a Fuel Junction Block (see 1/25 SCALE/ENGINE RELATED/FUEL MANAGEMENT). Also see the Braided Lines, Hard Lines, Soft Lines and Fittings along with the SMALL or...

Flathead Air Cleaners (Spun Aluminum) 1/25

Two small machined aluminum air cleaners. Polished, domed air cleaners with rings around the bottom edge. They have a pin on the bottom and a point on the top of the dome.   Two aluminum pieces by Parts by Parks, 1/25 scale.

Blower Starter Bracket, 1/16

Unless your blown engine has its own starter, you'll need to start it with a blower starter. This bracket holds the blower starter and will add that special touch of detail to your engine. Here is a photo of a real-world starter. The pins fit into the...

Throttle Linkage Set, 1/25

A throttle linkage set with pins added to the ends of the linkage components. This will provide a more stable attachment point for linkage rods, etc. Depending on your attachment, the pin may have to be bent 90 degrees.   Photo etched...

Round Air Cleaner, Spun Aluminum, 1/25

A realistic round spun aluminum Air Cleaner. It has a screen air filter between the top and bottom halves. Dimensions: Diameter - .45" Overall Height - .19"   No assembly required.   By Parts by Parks, 1/25 scale.

Hose Clamps Tie Wraps 1/24-1/25

Enough clamps and tie wraps for many cars. Leave them looking like stainless steel or paint the black or white. Ideal for your radiator hoses and heater hoses. Wrap them around your muffler or exhaust tip connections. The longer pieces could fit...

Injector Stacks - Long 1/24-1/25

Smaller, polished aluminum injector stacks for a Hilborn style induction system. Pack contains 8 stacks, polished aluminum with a flared top. . The stacks are hollow with a 'pin' at the bottom for easy mounting Dimensions per back of...

Injector Stacks - Small 1/24-1/25

Smaller, polished aluminum injector stacks for a Hilborn style induction system. Pack contains 8 stacks, polished aluminum with a flared top. . The stacks are hollow with a 'pin' at the bottom for easy mounting Dimensions per back of...

Velocity Stacks, Small, 4bbl Carb 1/24-1/25

Smaller, polished aluminum velocity stacks for a 4bbl carburetor. Pack contains 2 stacks, turned solid aluminum, so there's no seam. The stack is hollowed-out, leaving a solid bottom.  You could drill it out so that you'd be able to see the carb...

Holley Dominator Carb & PE Details, Pair 1/25

Holley Dominator Ultra Detail Carb Kit with Photo Etch Air Horn and Linkage.  These carbs were drawn in CAD and capture as many features as possible of Holley's decades-famous Dominator race carb. The carb bodies are 3D-printed and are...

Soft Line - Hose .011", .29mm OD

This is a shiny black nylon line. It is slightly springy and can be bent at sharp anglesThe OD dimension is .008" or .20mm.  This soft line equals the following equivalent 1:1 size at each scale.1/25 scale = 9/32"1/16 scale = 1/12 scale =1/8...

Soft Line - Hose .005", .12mm OD

This is the smallest black soft line I have. This is a shiny black nylon line. It is slightly springy and can be bent at sharp anglesThe OD dimension is .0047" or .14mm.  Typical uses are small oil lines, vacuum and fuel lines, especially fuel...

Soft Clear Line - Hose .005", .13mm OD

This is my smallest clear line.  You can barely see it, but if you need a really small clear line, this is it.This could be used for a 1/25 radiator overflow tube, small carburetor fuel lines, or other clear line needed.  This soft line is easy...

7-1/2" Diameter Dual Air Cleaners, 1/24-1/25

A pair of small air cleaners that will fit a 4bbl carb. At 1/24 scale they equal 7.5" diameter At 1/25 scale they equal 7.8" diameter. It consists of a semi-coned aluminum top and flat aluminum bottom, with screen material in between. Here is an...

8" Diameter Dual Air Cleaners, 1/25

A pair of small air cleaners that will fit a 4bbl carb. It consists of an aluminum top and bottom with screen material.  The top is peaked in the center   Two complete air cleaners, by Detail Master, 1/25 scale.  

Injector Velocity Stacks 1/25

Shiny aluminum injector stacks (tubes) for that early style Hilborn injected engine. Dimensions:Length: .62", (5/8")Diameter - OD (tube): .125", (1/6") These stacks are hollowed and flared at the top and solid at the bottom They can also be used as...

Weber Small Velocity Stacks 1/24-1/25

This will add that special detail to your Weber induction system or you may find other uses for them. They are hand turned, solid, billet aluminum stacks and there are no seams. They can be used on a standard kit engine.  The bottom diameter is ...

Soft Line - Red .016", .4mm OD

This is a small, soft, solid, semi-shiny line.  It can bend at a sharp angle without kinking.See Size A1 Ferrules for this soft line. This soft line equals the following equivalent 1:1 size at each scale.1/25 scale = 3/8"1/16 scale = 1/4"1/12...

Soft Black Line - Hose .016", .4mm OD

This is a small, soft, solid, semi-shiny line . It's the perfect thing for those small fuel lines at the engine. It can bend at a sharp angle without kinking.See Size A1 Ferrules for this soft line. This soft line equals the following equivalent...

Soft Clear Line - Hose .008", .2mm OD

This is really small, soft, solid, clear line . You can barely see it, but if you need a really small clear line, this is it.This could be used for a 1/25 radiator overflow tube, small carburetor fuel lines, or other clear line needed.  This soft...

Soft Clear Line - Hose .012", .3mm OD

This is a pretty small soft, solid, clear line . It's the perfect thing for those small fuel lines at the engine.  It can bend at a sharp angle without kinking.See Size A1 Ferrules for this soft line. This soft line equals the following...

Blower Scoop Hardware Set 1/24-1/25

Everything you need to detail that blower and injection hat. Includes: Blower and hat hold-down platesSpark plug wire loomsAssorted bracketsLinkage fittingsIntake butterfliesBlower belt safety guardand moreStainless Steel and shiny right out of the...

LS, BBC EFI Ram IntakeManifold, 1/25

A 3D-printed EFI manifold for a BBC or HEMI engine. This is one of my latest designs which I'm also making in a CNC machined aluminum version. With low restrictive rounded runners for maximum horsepower as well as improved low end torque for great...

4-Pulley Set, 1-Groove, Flathead or Other 1/25

A set of four spun aluminum V-groove pulleys. This is packaged as a Flathead pulley set but can be used for most any engine requiring smaller single groove pulleys. Consists of four single groove pulleys: Crank pulley Water pump pulley Fan...

Black Ferrule Fittings for Braided, Soft, Hard Lines

The latest trend in TF or FC is black fuel lines with black anodized fittings. You see them for blower injector lines, Injector-hat injection lines and more. These lines are black braided lines with black anodized AN fittings.  Typically these...

Tall 4-Hole TF-PM Hat #1 1/25

A four square-hole, tall Injector Hat similar to what you find on TF and PM cars Molded in one piece. Contains 1 resin hat.

Soft Line - Hose or Cable .031", .8mm OD Dia.

This is a solid soft line that looks like real rubber. It is easily configured to the space you have. It's able to bend at a sharp angle without kinking. At 1/25 scale, use for heater hose, air conditioning hose and more.Makes perfect spark plug cable...

Molded Blower Belt with Pulleys 1/25

A more detailed blower belt set than found in kits. The belt shows cogs on the inside and bolt heads are found on the pulleys. Also has the blower pulley, crank pulley and idler pulley molded in..   Blower pulley to Crank pulley center-to-center...